Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

两种中温固化胶粘剂的剪切疲劳和蠕变性能研究

研究了SY 2 4B胶膜和SY H2糊状胶粘剂的剪切疲劳和蠕变性能。SY 2 4B胶膜和SY H2糊状胶粘剂同为中温固化的结构胶粘剂 ,SY 2 4B胶膜采用橡胶增韧 ,SY H2糊状胶粘剂采用热塑性树脂增韧。SY 2 4B胶膜虽然具有优异的韧性 ,但SY H2糊状胶粘剂的剪切疲劳和蠕变性能优于SY 2 4B胶膜 ,这与增韧剂种类与胶层厚度有一定关系。温度、应力和时间也是影响蠕变量的重要因素     

新型活动密封件的研究与应用

根据飞机液压系统橡胶密封圈使用中易出现老化,引起串油、串气等故障问题,结合某机型试验提出新材料密封圈改进方案,以满足系统的高温及动密封性使用要求。试验结果表明,新材料密封圈适合高温、动密封部位的使用,可以替代丁腈试5171橡胶密封圈,应用于液压系统,提高系统性能。     

Kinetic Monte Carlo Simulation of EB-PVD Film:Effects of Substrate Temperature

The 2D kinetic Monte Carlo (KMC) simulation was used to study the effects of different substrate temperatures on the microstruc-ture of Ni-Cr films in the process of deposition by the electron beam physical vapor deposition (EB-PVD). In the KMC model, substrate was assumed to be a “surface” of tight-packed rows, and the simulation includes two phenomena: adatom-surface collision and adatom diffusion. While the interaction between atoms was described by the embedded atom method, the jumping energy was calculated by the molecular static (MS) calculation. The initial location of the adatom was defined by the Momentum Scheme. The results reveal that there exists a critical substrate temperature which means that the lowest packing density and the highest surface roughness structure will be achieved when the temperature is lower than the smaller critical value, while the roughness of both surfaces and the void contents keep decreasing with the substrate temperature increasing until it reaches the higher critical value. The results also indicate that the critical substrate temperature rises as the deposition rate increases.     

钛合金板材激光弯曲成形的研究

 对常温下钛合金板材进行了激光弯曲成形研究。分析了激光功率、扫描速度、光斑大小对板材弯曲变形的影响,获得理想工艺参数范围为:功率1 .0～1 .2 k W、扫描速度2～3 m/min、光斑直径6～7mm。同时分析了板材厚度、宽度及扫描次数对材料弯曲变形的影响,为钛合金板材弯曲成形提供了一种新途径。     

考虑可压缩与热传导的壁面函数边界条件及其应用

考虑到可压缩和热传导效应的壁面函数边界条件,被耦合到了采用k-ω两方程湍流模型、用有限体积法求解N-S方程的程序中。壁面函数基于耦合的速度和温度型,并且在边界层内的粘性子区和对数区内一致有效。引入壁面函数边界条件后,通过算例验证在y <100的范围内,得到的物面压力、摩阻、热流与实验结果比较,结果可靠。而无壁面函数边界条件时,要得到相同精度的结果,要求y ≈1。壁面函数的引入,为工程上准确预测飞行器在湍流流动中表面受力与气动热提供了保障。     

双温度试验系统方案设计

结合双温度试验系统方案设计,介绍了可编程控制器在温度控制上的应用,有助于增进读者对PLC等的了解。     

翼型风洞侧壁干扰的数值模拟研究

运用Navier-Stokes数值模拟对翼型模拟试验对风洞侧壁干扰进行模拟，将简单代数湍流模型扩展用于机翼／风洞侧壁结合区流动，分析了风洞实验侧壁干扰问题的形成机理和影响翼型实验侧壁干扰的各种因素，如翼型展长、风洞侧壁边界层厚度及侧壁边界层抽吸等，对实验结果的影响，得出了一些有用的结论。计算格式空间采用中心有限体积离散，时间采用多步Runge-Kutta时间步长格式进行积分。计算结果证明了该方法的可行性和优越性。     

航空发动机涡轮前温度场数据分析方法

在航空发动机整机测试条件下,温度场测试具有局限性。介绍了1种发动机涡轮前温度场测试数据的统计分析方法,该统计方法较为有效;引入模糊原理,对统计量进行了概率分析,使得统计量评估更加完善。     

高升力多段翼型洞壁干扰修正

 Erisson对高升力多段翼型的洞壁干扰问题进行过理论计算。Moury和Labrujère对上述问题也进行过一些研究,可惜Moury的实验是在开闭比为20％的开孔壁风洞中进行的,而Labrujère仅给出个别情况的实验结果,且其测压点较多,计算较繁,不易实时处理。